Home > News Center > Product News

MARTENSITIC JIS G4304 SUS 420J1 stainless steel plasma cutting

MARTENSITIC JIS G4304 SUS 420J1 stainless steel plasma cutting

Plasma cutting MARTENSITICJIS G4304 SUS 420J1 stainless steel is a cutting of MARTENSITICJISG4304 SUS 420J1 stainless steel by plasma arc flame. Since the temperature of the plasma arc is as high as about 15000-30000'0, the metal material can be melted or even vaporized in a very short time, so that it can be cut for metals with high temperature resistance, good thermal conductivity and easy oxidation, such as For the cutting of MARTENSITICJISG4304 SUS 420J1 stainless steel, cutting of copper, aluminum and aluminum alloy. Nowadays, the commonly used plasma cutting machine is divided into two types: automatic and automatic. The cutting machine consists of a manual (or automatic) torch, control box, and DC power a.

 

Hand-held plasma cutting machine, currently available in LG 1-400 and LG 3-400, for manual cutting of straight lines and various geometries, manual plasma cutting machine, cutting MARTENSITICJIS G4304 SUS 420J1 stainless steel plate with a maximum thickness of 40 m Come. Cutting MARTENSITICJIS G4304 SUS 420J stainless steel plate has a maximum thickness of 80-100 mm, and the diameter of the automatic cutting circle is (k 200.0 1000 mm. The gas for plasma cutting is nitrogen, hydrogen, hydrogen nitrogen, hydrogen hydrogen. Currently used up to a Gas, because the nitrogen hot pressing effect is stronger than m gas, and it does not react with copper spray It, the purity of nitrogen is generally not lower than 5%, otherwise it is easy to burn out the nozzle and tungsten. Using plasma cutting machine The cut metal surface is smooth, the cutting gap is narrow, and the cutting speed is high.

 

Plasma cutting MARTENSITICJIS G4304 SUS 420J1 stainless steel will produce a large amount of metal vapor and nitrogen oxides INO:, N2 00 gas, at the same time, due to strong ultraviolet radiation, the oxygen in the air becomes ozone og, if the concentration is higher, to people The respiratory system is hurtful. Therefore, the working site using plasma cutting equipment should be sufficiently spacious and air ventilated. Or should be equipped with a ventilation dust collector N, a plasma cutting machine with a general dust exhaust device, which is harmful when cutting MARTENSITIC JIS G4304 SUS 420J1 stainless steel. Gas can be controlled below national health standards.

 

The ventilation and dust removal device of the plasma cutting machine can be installed according to the conditions of each factory, and can be equipped with a dust remover and an exhaust fan. The following describes a ventilation and dust removal device (Fig. 2-9). This device uses two air volumes of 1,100. The scoop-hour ventilator is exhausted by two channels, concentrated on one duct to the top of the roof, and the MARTENSITIC JIS G4304 SUS 420J1  workpiece is cut on a toothed cast iron plate.

 

MARTENSITIC JIS G4304 SUS 420J1 stainless steel is the main product of katalor. We not only mention MARTENSITICJIS G4304 SUS 420J1 stainless steel but also provide cutting services for stainless steel plates. If you have any needs in this area or simply buy MARTENSITIC JIS G4304 SUS 420J1 stainless steel from us, please contact us.

 

Pre: FERRITE GB4237 1Cr17 stainless steel weld pickling, passivation treatment

Next: Vietnam announces anti-dumping duties on imported stainless steel products from China, Malaysia and

Contact Us

Shanghai Katalor Enterprises Co., Ltd

0086-21-61182423
0086-21-61182425
[email protected]
No.230,1st Floor,Building No.1,No.221 Of Huashen Road,Free Trade Area Of Pudong New District,Shanghai China
Live Chat